Skip to content

Florida certified pool contractor · CPC1461119 · CPC1460562

Get a Free Estimate
Home
Services
About Us
Project Gallery
Resources
financingContact Us
Get a Free Estimate

Do You Need a Permit for a Pool Screen Enclosure in Florida? What the Building Code Asks For

A pool cage is a structure, so building, enlarging or rebuilding one needs a permit. The permit is really a check on one number, the wind the frame is designed for at your address, and on what the drawings assume about the site, the mesh and the footings.

  • By Robert Wesley Brannen
  • Published
New concrete slab poured in a sandy yard beside a house with a black screen enclosure, under a cloudy sky, with pipes in the foreground.

Yes. Section 105.1 of the Florida Building Code requires a permit before anyone constructs, enlarges, alters or repairs a structure the code regulates, and a pool screen enclosure is one: Chapter 20 sets its minimum aluminum thickness and the wind loads it must resist. Florida's list of work exempt from permits has no line for screen enclosures. In unincorporated Alachua County, the pool plan-review requirements state it directly: a screen enclosure "will require a separate permit."

What the permit really checks is one number and the assumptions behind it: the wind speed the frame is designed for at your address, the exposure of the site, the mesh, and the footings that hold it down.

The rules that decide the permit

RuleWhere it comes from
A permit is required to construct, enlarge, alter or repair a regulated structureFBC Building 105.1
Extruded aluminum members at least **0.040 inch** thickFBC Building 2002.3.1
Frame designed for wind in **two directions**, using the pressures in Table 2002.4FBC Building 2002.4
Each primary member also designed for a **300-pound** vertical load on any 1 footFBC Building 2002.4
The AAF Guide to Aluminum Construction in High Wind Areas is accepted engineering practiceFBC Building 2002.4.1
Residential screen enclosures use **Risk Category I** wind speedsFBC Residential R301.2.1.1.1.1
A screen enclosure can be part or all of the pool barrierFBC Residential R4501.17.1.11

These are from the 8th Edition (2023) of the Florida Building Code, which is in effect until the 9th Edition starts on December 31, 2026. The note at the end covers the one change the 9th Edition makes to this section.

Is any of it exempt?

The building volume's exemption list in Florida covers gas, mechanical and plumbing work. It has no exemption for an enclosure, a new one or a rebuilt one.

The only route around a permit is section 105.2.2, which lets the building official approve ordinary minor repairs without one. That is the official's call, not the contractor's. Rescreening a few torn panels may fall there in your jurisdiction, or it may not: ask the building department before the work starts. Alachua County's permit page says the same thing in plainer words, that redecorating and minor repairs generally do not need a permit and that you should call the Building Division if you are unsure.

Old pool with blue waterline tile and a weathered concrete deck, under a screen enclosure that is partly stripped of its screen.

What is not a minor repair is anything that changes the structure: a new cage, a taller or longer one, a frame replaced after a storm, a solid roof section added, or a cage rebuilt as part of a pool remodel.

What the permit reviews: the wind

A screen enclosure is designed for wind blowing at it from two directions, using a table of pressures in the code. Table 2002.4 gives those pressures by design wind speed, from 110 to 170 mph, and by exposure category. Three inputs decide which cell of that table your cage is designed from.

1. The wind speed at your address. It is not one number for Florida, and it is not always one number for a county. Under the residential code, screen enclosures are designed to the Risk Category I wind map. The City of Gainesville's design requirements list 120 mph for Risk Category I and 130 mph for Risk Category II, measured as Exposure C at 33 feet. We did not find an equivalent published figure for Ocala or Marion County. For any address, the Florida Building Commission's wind-load fact sheet describes the free ASCE Hazard Tool, which takes an address or coordinates and returns the design wind speed.

2. The exposure of the site. The code defines three. Exposure B is urban and suburban areas, wooded areas, or terrain with many closely spaced obstructions the size of houses. Exposure D is flat, unobstructed areas and water surfaces. Exposure C is everything in between, including open terrain with scattered obstructions, flat open country and grasslands. A cage facing a lake or an open pasture is not designed like one tucked between two-story houses, and the pressures in the table rise from B to C to D.

3. The mesh. The table's pressures assume standard 20 × 20 mesh. For a coarser 18 × 14 mesh, the code allows the pressures on the screen to be reduced. For mesh denser than 20 × 20, it requires the pressures used for an enclosed building. That is why tighter insect or privacy screen is an engineering choice, not a finish picked at the end.

Height matters too: the table is written for a cage with a mean roof height of 30 feet, and a separate table adjusts it for other heights.

Ask any bidder which wind speed, which exposure category and which mesh the drawings assume. Two quotes designed to different answers are two different structures, which is the point our guide to what a pool screen enclosure costs makes about price.

Cages designed to lose their screen in a storm

The code allows a second way to design a cage: on the assumption that some screen panels will be removed, retracted or cut before a storm, which lowers the load on the frame. Section 2002.7 allows it only with conditions:

  • the design must be signed and sealed, site-specific engineering;
  • it must still work with every screen panel in place at the 110 mph column of the table;
  • the panels to be removed or cut must be marked on the frame with permanent labels, and reaching them must not require ladders or scaffolding;
  • screen designated to be cut must be completely cut when winds over 75 mph are forecast;
  • the contractor must give the owner one-time replacement screen for the cut panels, and written notice to the owner and the building department of the owner's duty to remove or cut them;
  • if the cage is the pool barrier, the barrier height must hold with those panels out.

If a quote is noticeably lighter than the others, ask whether it uses this method. It is legitimate, but it hands you a job to do before every hurricane. The same chapter requires vinyl, glass and acrylic panels on an enclosure to be removable, with a decal saying they must be removed when winds exceed 75 mph.

White aluminum screen enclosure over a pool with an attached spa and a covered patio with an awning, palms visible through the screen.

Product approval: what to ask for

Florida's product approval rule covers eight categories of products: panel walls, exterior doors, roofing, skylights, windows, shutters, structural components and impact protective systems. Screen mesh and screen enclosure framing are not named in the subcategories. Anchors are, under structural components.

State law also says that products custom fabricated or assembled do not need separate approval, provided their component parts are approved for that use. A cage built from extrusions on your deck falls there. So the practical question is not whether "the cage" has an approval number. It is which approved components the drawings rely on, such as the anchors, and any solid roof panels or doors that are part of the project. Each approved product has an FL number that anyone can look up in the Florida Building Commission's product approval search.

Who pulls the permit

The contractor building the cage, under a license that covers it. Florida's rule for the specialty structure contractor license lists screened porches, screened enclosures and pool enclosures within that license's scope, along with their incidental foundations and slabs. Whoever pulls the permit, you can confirm the license in the state's public register before signing, and the permit should carry the same name as the contract.

A new pool and a new cage: two permits, one plan

The pool and the enclosure are separate permits, but they are one design. Alachua County's pool plan-review requirements ask the applicant to indicate, at the time of application, any retaining walls or footings being installed for future screen enclosures. Its older pool inspection checklist lists the foundation for a screen enclosure at the deck inspection, and the bonding of all metal parts, enclosure included, at the final.

In practice that means the cage's footings are drawn with the deck, so its posts never land on pool plumbing, and the cage doors are planned as pool gates. The Florida Building Code lets a standard screen enclosure serve as part or all of the pool barrier, and our guide to Florida pool barrier requirements covers what its doors have to do to pass. Whether a cage is worth it at all, against open deck and a fence, is a separate question, covered in whether a screened-in pool is worth it in Florida.

In Gainesville and Ocala

Which office reviews the permit depends on the parcel, not the mailing address: inside Gainesville or Ocala city limits it is the city, and outside them it is Alachua or Marion County. Our guides to pool permits in Gainesville and Alachua County and pool permits in Ocala and Marion County explain how to tell, and the pool permit office finder links each office. The full statewide set of pool permits is in what permits a Florida pool needs.

Two local points belong in the design conversation. In Gainesville, the city's published wind speeds give the engineer a starting number. And on the larger lots outside both cities, the exposure question is real: a cage that faces open pasture or a wide lake is a different structure from one sheltered by houses and trees.

We design enclosures with the pool and the deck. Our pages on custom pools in Gainesville and Alachua County and pool builders in Ocala explain how the pieces are sequenced, and our pool screen enclosures page shows the enclosures themselves. Our pool cost estimator carries a cage built with a new pool as a $15,000 planning line.

A note on the 9th Edition

The Florida Building Commission's analysis of changes for the 9th Edition (2026) adds one section on screen enclosures: aluminum members with spline grooves that hold screen must be 6005-T5 alloy or better, and the supplier must document the alloy for the building official or inspector. It lists no other change to the screen enclosure sections. We will update this guide when the 9th Edition text is final.

Plan the cage with the pool

If you are building a pool and want the enclosure, its footings and its doors designed into it from the start, begin with a design-build evaluation. We will confirm the permit office, the wind speed and the exposure for your address before anything is drawn.

Common questions

Do you need a permit for a pool screen enclosure in Florida?

Yes. Section 105.1 of the Florida Building Code requires a permit before anyone constructs, enlarges, alters or repairs a structure the code regulates, and screen enclosures are regulated in Chapter 20. Florida's list of permit exemptions has no line for them. In unincorporated Alachua County, the pool plan-review requirements say a screen enclosure needs a separate permit.

Do I need a permit to rescreen my pool cage?

Ask your building department before the work starts. The Florida Building Code has no exemption written for rescreening; the closest provision lets the building official approve ordinary minor repairs without a permit. Whether replacing screen panels counts is the official's decision, not the contractor's.

What wind speed is a pool cage designed for in Gainesville?

The City of Gainesville's design requirements under the 8th Edition list 120 mph for Risk Category I and 130 mph for Risk Category II structures, Exposure C at 33 feet. The residential code designs screen enclosures to the Risk Category I map. Outside the city, check the address in the free ASCE Hazard Tool.

Can a screen enclosure be my pool barrier?

Yes. The Florida Building Code allows a standard screen enclosure that meets the barrier requirements to serve as part or all of the pool barrier. Its doors are treated like gates, and if the cage is designed with removable or cut-out screen panels, the barrier height has to hold with those panels out.

Who can pull the permit for a pool enclosure?

A contractor whose license covers the work. Florida's specialty structure contractor rule lists screened enclosures and pool enclosures within that license's scope. Whoever pulls it, the license can be checked in the state's public register before you sign.

Sources

About the author

Robert Wesley Brannen

Robert Wesley Brannen is the co-founder of Mr. & Mrs. Outdoor Living and a Florida-certified pool and spa contractor. Having started in his family's aluminum business at age 13 and previously led Happy House Outdoor Living, Robert brings extensive experience in custom pool construction, outdoor structures, and design-build project management.

Florida Licenses: CPC1460562 · CPC1461119 · SCC131153553.

Request a Design-Build Project Evaluation

Share your property details, project scope, and investment range. Our licensed design-build pool builders will review your request and confirm alignment before next steps.

Get a Free Estimate
New rectangular pool with raised mosaic spa, sun shelves with loungers and an ivory travertine deck.
Call us
Get a Free Estimate